ASSESSMENT OF THE TECHNICAL CONDITION AND IMPACT OF HAZARDOUS FIRE FACTORS ON VEHICLE COMPONENTS
DOI:
https://doi.org/10.32782/forensic.science.2026.4.24Keywords:
vehicle fire, technical condition, hazardous fire factors, thermal damage, fuel system depressurization, metal hardness, Leeb method, portable hardness tester, automotive (engineering-transport) expertiseAbstract
This article summarizes the results of forensic practice in examining vehicle components that were directly exposed to fire-induced thermal impact, using a portable dynamic hardness tester based on the Leeb method to measure the surface hardness of structural parts. Using the examination of the engine compartment of a BMW as a case study, in which the question of a possible loss of fuel system integrity was addressed, and taking into account the provisions of the current methodologies of forensic vehicleengineering and fire-technical examinations [1; 3; 5; 8; 9], the visual signs of thermal damage are compared with the readings of the hardness tester, converted by the instrument into Brinell hardness (HB) units. It is shown that the interpretation of the results requires consideration of the alloy grade, its initial structural state, the part geometry, the condition of the tested surface, and the measurement conditions. It is established that hardness values alone do not allow determination of the maximum heating temperature or localization of the fire origin; however, they can be used as a supplementary comparative indicator in combination with the results of visual inspection, analysis of the nature of thermal damage, metallographic and chemical examinations, and other case materials. The relevance of the study is determined by the prevalence of vehicle fires and the difficulty of assessing the technical condition of vehicle components after exposure to flame, thermal radiation, and elevated temperatures. Significant thermal damage to parts can complicate the identification of the primary technical malfunction, in particular a loss of fuel system integrity, as well as the determination of the nature and localization of the thermal impact. Therefore, an integrated approach that combines visual examination with instrumental methods is of particular relevance.
References
1. Інструкція про призначення та проведення судових експертиз та експертних досліджень : затв. наказом Міністерства юстиції України від 08.10.1998 № 53/5 (у редакції наказу Міністерства юстиції України від 27.07.2015 № 1350/5).
2. Збірник методик автотехнічних експертиз: 10.1 Дослідження обставин ДТП; 10.2 Дослідження технічного стану транспортних засобів ; 10.3 Дослідження деталей транспортних засобів ; 10.4 Транспортно-трасологічні дослідження; 4.3 Криміналістичне дослідження транспортних засобів / Київ. НДІСЕ, Нац. наук. центр «Інститут судових експертиз ім. Заслуженого проф. М. С. Бокаріуса», Одес. НДІСЕ, Львів. НДІСЕ, Донец. від-ня Нац. наук. центру «Інститут судових експертиз ім. Заслуженого проф. М. С. Бокаріуса», Дніпроп. НДІСЕ. Київ : М-во юстиції України, 2024. Реєстр. код 10.0.18.
3. Загальна методика призначення та проведення комплексних судових експертиз, що виконуються комісією експертів : із змінами, внесеними рішенням Координац. ради від 12.09.2014 (реєстр. код 0.1.16).
4. ДСТУ 3649:2010. Колісні транспортні засоби. Вимоги щодо безпечності технічного стану та методи контролювання. Київ : Держспоживстандарт України, 2010.
5. ДСТУ 2272:2006. Пожежна безпека. Терміни та визначення основних понять. Київ : Держспоживстандарт України, 2006.
6. ДСТУ 7688:2015. Паливо дизельне ЄВРО. Технічні умови. Київ : ДП «УкрНДНЦ», 2015.
7. ДСТУ 7687:2015. Бензини автомобільні ЄВРО. Технічні умови. Київ : ДП «УкрНДНЦ», 2015.
8. Гаврилюк А. Ф. Пожежна небезпека колісних транспортних засобів : монографія. Львів : ЛДУБЖ, 2018.
9. Матіюк О. О., Рябінін І. М., Гусейнов Р. Н., Шебалков І. Л. Дослідження зовнішніх (візуальних) ознак наявності легкозаймистих і горючих рідин, виявлених на місці пожежі. Луцьк, 2020.
10. Єдигарян Ф. С., Гардерман В. Д. Методи встановлення причин і часу руйнування деталей автотранспортних засобів, що впливають на безпеку руху. Київ : КНДІСЕ, 1972.
11. ISO 16859-1:2015. Metallic materials. Leeb hardness test. Part 1: Test method. Geneva : ISO, 2015.
12. ASTM A956/A956M-22. Standard test method for Leeb hardness testing of steel products. West Conshohocken : ASTM International, 2022. DOI: https://doi.org/10.1520/A0956_A0956M-22.
13. Summers P. T., Case S. W., Lattimer B. Y. Residual mechanical properties of aluminum alloys AA5083-H116 and AA6061-T651 after fire. Engineering Structures. 2014. Vol. 76. P. 49–61. DOI: https://doi.org/10.1016/j.engstruct.2014.06.033.
14. Liu Y., Liu H., Chen Z. Post-fire mechanical properties of aluminum alloy 6082-T6. Construction and Building Materials. 2019. Vol. 196. P. 256–266. DOI: https://doi.org/10.1016/j.conbuildmat.2018.10.237.



